The HardiePlank transfer track is available in 12 feet. lengths. Nominal widths from 51/4″ to 12″ create a range of exposures from 4″ to 103/4″.

You should also know how thick Hardie planks are?

Specifications

Serial Name HZ10 HardiePlank
Type Overlap Paneling
Actual Thickness (inches) 0.312
Actual Length (inches) 144, 0
Actual width (inches) 8.25

And what is a Hardie Plank?

A combination of cellulosic fibers and cementitious materials, HardiePlank is a fiber cement siding that comes in long, horizontal strips, just like wood formwork siding. HardiePlank is part wood in the form of cellulose and part mineral.

Considering what nails do you use for Hardie panels?

NAIL TYPE:

Fastening elements must be corrosion-resistant, galvanized or made of stainless steel. Electro zinc plated nails are acceptable for use with James Hardie Siding products but may exhibit premature corrosion. James Hardie recommends using quality, hot-dip galvanized nails.

Is Hardie board expensive?

Cost. There’s no doubt the benefits of Hardie boards come at a price. Vinyl siding is far more affordable, both in terms of the product itself and the labor cost of installing it.

How much does Hardie siding cost?

Hardie slab siding costs about $0.70 $5.25 per square foot. This could result in a total cost of between $4,700 and $13,300.

Does Lowes stock James Hardie siding?

James Hardie Vertical siding Fiber Cement Siding at Lowes.com.

Does Hardie panel need to be painted?

Painting: Hardie panel siding is known to hold paint longer than wood. Because it’s moisture resistant, it never swells or rots, so the paint never peels, chips, or cracks. It’s also available in a variety of pre-painted colors to choose from so you can pick the right shade without lifting a finger.

Can you put screws in Hardie planks?

Blind nailing is the preferred installation method for HardiePlank. The term refers to a nail/screw method of joining HardiePlank planks to conceal nail or screw fasteners. Use a number 8, 1-1/4 in. long and .375 in. wide (HD), ribbed wafer head (or equivalent) for screwing on steel studs.

Is Hardie plate fireproof?

Yes, HardieBacker® 1/4″ Cement Board is considered non-combustible when tested to ASTM E 136 and can be used in conjunction with other non-combustible materials around a fireplace. This does not mean clearances to combustible Building materials can be reduced by using HardieBacker 1/4″.

How often does Hardie board need to be painted?

On average, a quality 100% acrylic exterior paint should last all over five to 15 years on fiber cement that has been properly primed at the factory, as long as the paint has been applied correctly and there has been no unusual damage to the house.

Can I use a frame nailer on Hardie siding?

The answer is yes. Frame nail guns can be used for side panel installation if the nail used is long enough to firmly attach the side panel to your outer wood sheathing. While it’s recommended to always use a nail gun when installing side panels, you can use a frame nailer instead in a pinch.

Can you use screws on Hardie side panels?

HardiePlank ® Overlap Panels can be used with fasteners approved by ICC-ES ESR-2290 and located in accordance with wind load tables. Fastening elements must be corrosion-resistant, galvanized or made of stainless steel. Fasteners must be installed between 1 inch.

Can you stain hardie planks?

Hardiplank siding is a durable, fireproof building material that resembles natural wood. As this is a concrete based product it cannot be stained in the traditional sense. By being extra careful when applying, your Hardiplank siding can mimic the look of naturally stained wood.

Can I screw into Hardiplank?

“Use a designated drill bit Concrete. Drill the holes so the screw threads will anchor into the wall studs – not just the hardiplank or sheathing. The hardiplank itself is too brittle to carry much additional weight or wind load.

How do you remove the hardie plate trim?

How to remove the hardie plank

  1. Carefully slide the thin edge of a flat pry bar under the bottom edge of the first piece of hardie plank to be removed Cladding.
  2. Carefully pry the piece of cladding towards you so you can see the nail or screw pattern used to attach the planks to the substructure.

Is hardie board cheaper than brick?

A At face value, fiber cement siding appears to cost less than brick. However, when maintenance and painting are factored into the cost of construction, brick becomes a much better value for homeowners and builders. Brick is inherently insect and moisture resistant. The same is not true for wood and fiber cement siding.

How many square feet does Hardie planks cover?

The average cost to stay a 1,500 square foot home with Hardie Plank siding is $12,000 -18,000. Cost of painted Hardie Plank fairings.

Board Exposure Cost per 12′ board Cost / square meter (100 square feet)
6″ exposure $11.20 $190.40/square
7″ exposure $13.27 $185.78/square

Is Hardie board waterproof?

INTRODUCTION: THE FIRST & ONLY WATERPROOF CEMENT BACKBOARD. The all-new HardieBacker® Cement Board with HydroDefense™ technology offers exceptional performance with a waterproof composition throughout the board.

Can I use roofing nails on Hardie siding?

You can blast Hardie siding with air-powered nailers or use hand-powered roofing tacks to attach the siding to the house or building. The nails can be ring shaped or plain, just make sure you hit the studs in the wall. Nails driven in too high will not hold, as will nails driven in too hard.

Can you pressure wash Hardiplank?

You can achieve the same shine on the side wall of your house by cleaning it in – or twice a year. Don’t use a pressure washer to get the job done, as a low-pressure hose and a soft, medium-bristle (non-metal) brush has been found to be the best way to remove dirt and debris from James Hardie® fairings and fairings.

Can you nail Hardie Backerboard?

When applying HardieBacker 500 cement board to plasterboard, use corrosion resistant roofing nails at least 1-3/4″ long. For countertops: At least 3/4″ long corrosion-resistant roofing nails. Use corrosion-resistant roofing nails or countersunk ribbed screws at least 1-1/4″ long for HardieBacker 500 cement board.