The LP error indicates no drain and is usually a problem with the drain pump. Excess foam can also cause this error. Try running the washing machine through a rinse cycle with no load or soap.

And what does ND mean on my washing machine?

The nd error code on your Samsung front-load washing machine means that no water runs out of the washing machine. The likely causes are a clogged washing machine drain or a clogged drain pump filter.

How do you open a locked Amana washing machine? The Amana Front Load washing machine door is locked when installed

  1. The door can be unlocked immediately.
  2. The door lock LED light will flash. The door should unlock after 60 seconds.
  3. The washing machine will go into a hold and drain routine for 8 minutes. After 8 minutes, the door will unlock.

In this context, why is my Amana washing machine not spinning?

The Amana washing machine is not spinning. The lid switch assembly prevents the washing machine from rotating when the lid is open. If the lid switch assembly fails, the washing machine will not spin. If the washing machine is overloaded, the motor clutch will fail to protect both the motor and the gearbox.

How to test a washing machine pump?

How to use an ohmmeter Testing a washing machine pump

  1. Check the washing machine‘s power cord to make sure it is unplugged.
  2. Turn on the ohmmeter and touch the probes together. Set the dial to zero.
  3. Locate the two wires that connect to the side of the pump.
  4. Touch a probe on each of the connectors on the pump.

Who makes Amana dishwashers?

Whirlpool Corp.

How to troubleshoot an Amana washing machine?

How to troubleshoot an Amana washing machine

  1. Remove the top cover of the Amana washing machine. Insert a spatula between the top and front of the washer and push in to release the locking tab.
  2. Remove the connectors from the terminal by grasping the connectors and pulling.
  3. Check the pressure switch on the control panel.

How do I reset my Amana heavy duty washing machine?

Top loading washing machine – Hydrowave reset -Motors

  1. Unplug the washing machine for 1 minute.
  2. Plug the washing machine back in and raise and lower the lid 6 times within 12 seconds. You have 30 seconds to begin raising and lowering the lid.
  3. The motor has now reset and is ready to start a cycle.

Where is the drain filter on my Samsung washing machine?

All current Samsung front loading washing machines have dirt filter access panels located on the front of the unit. The filter is housed in the drain pump to prevent the drain hose from becoming clogged. If not cleaned regularly, you will experience unpleasant odours, drainage and filling problems.

Why is my Amana washing machine leaking at the bottom?

Amana washing machine is leaking water. The drain pump pumps water out of the drain hose. If the drain pump is cracked or damaged, or if the bearings are worn, the drain pump may leak water. Therefore, if water is leaking from the pan gasket, replace both the pan gasket and the pan bearings.

How do I drain the water from my Samsung washing machine?

[ Solution]
  1. 1 Unplug the washing machine from the mains.
  2. 2 Open the filter cover.
  3. 3 Unscrew the emergency drain cap by turning it to the left.
  4. 4 Grasp the cap on the end of the emergency drain hose, and then slowly pull it out about 15 cm (about 6 inches).
  5. 5 Drain all the water into a bowl.

How do you reset the Amana washing machine after a power failure?

Turn the rotary switch to the off position, turn off the power outlet , wait a minute, turn on the device and turn the dial back to the cycle and press the button. Turn the dial to the off position. Then press the power button down for about 20 seconds. It may help to reset the machine – it means it starts over.

Why is my washing machine lid locked?

If the door or lid doesn’t open at the end fails cycle, then the locking mechanism may be defective. Most washing machines have a manual release to unlock the mechanism and allow you to open the door or lid. The release is usually accessed from underneath the door lock or from inside the soap dispenser housing on some models.

How to unlock a front loading washing machine?

Manually unlocking a Kenmore front loading washing machine

  1. To unlock the control panel, touch “Control Lock” for five seconds until “CL” disappears from the washing machine display.
  2. Press “Start/Pause” to unlock manually Pause the cleaning cycle.
  3. Pull the door handle to open the door and add or remove laundry from the washing machine.

Why isn’t my washing machine draining or spinning?

If the washing machine won’t drain, there may be a clogged pump or hose. It is common for small socks or other small items of clothing to get into the water drainage system and clog the hose leading to the pump or the pump itself. If the washing machine does not drain, the lid switch assembly may be defective. This is a very common problem.

How do I troubleshoot my Samsung washing machine?

FIX SAMSUNG WASHING MACHINE/SOLUTION:

  1. Check or reset the fuse the circuit breaker.
  2. Straighten the drain hoses.
  3. Fix kinked hoses.
  4. If there is a drain restriction, fix it.
  5. Close it door and press the Start/Pause button.
  6. For your safety, your washing machine will not tumble or spin unless the door is closed.

How are you? Resetting a GE washer?

To reset washers that use the GE Hydrowave system, first unplug the washer for one minute. Plug the washer back in and quickly open and close the lid 6 times within 30 seconds. You must do this within 12 seconds.

Where is the coin trap on a washing machine?

Look for a coin trap. If your washing machine has a coin trap, you will see a small, square panel near the bottom on the front or side of the machine. Open the door and remove the trap by twisting it counterclockwise and pulling.