The area covered by 1 ton of asphalt depends on the thickness of the asphalt to be used; for a half-inch section of asphalt, 1 ton covers approximately 316 square feet, while 1 ton of asphalt covers 79 square feet when laid several inches thick.
Then you may also wonder how much asphalt is in a ton ?
The ton is currently used only in the United States and equals 2000 pounds (2000 lbs). The difference between the two isn’t huge, but it can quickly add up to a significant number as the quantity increases. Choosing the correct system of units in our Asphalt Calculator will help avoid this problem.
Do you also know how to calculate how much asphalt I need? To determine the amount of asphalt you need for a paver application, you first need to know the area to be paved.
- Volume = 17,257 sq.ft. × (4″ ÷ 12″/ft) = 5,752 cu.ft.
- Weight = 5,752 cu.ft. × 145 pcf = 834,040 lbs.
- Convert to tons = 834,040 lbs.
So how much is a ton of hot asphalt?
At $85 per ton for hot asphalt, asphalt is $85 times 30 times, or $2,550.
How many tons of asphalt are in a dump truck?
Our largest single dump truck can carry up to 20 Accommodate tons of cargo or 20 cubic yards of mulch.
How thick should my asphalt driveway be?
In many cases a 4-inch thickness may be sufficient, but 5 or even 6 inches of asphalt in full depth guarantee you a stronger, stable driveway under a wider range of climates and loads. As an option, some contractors use 6 to 8 inches of compacted aggregate or gravel as a base for 3 inches of asphalt pavement.
How much does a ton weigh?
Ton , unit of weight in the Avoirdupois system, representing 2,000 pounds (907.18 kg) in the United States (the short barrel) and 2,240 pounds (1,016.05 kg) in Great Britain (the long barrel). The ton used in most other countries is 1,000 kg, which is equivalent to 2,204.6 pounds avoirdupois.
How much does a dump truck load of asphalt cost?
A concrete driveway, 90 feet long and ten foot wide would be about $1800 for materials plus about $2000 for additional labor for a total cost of nearly $4000. A paved driveway costs $2 to $6 per square foot installed. For a 500 square foot (50 x 10) driveway, this works out to an average cost of $2500.
What is the cheapest way to pave a driveway?
Cheap ways to pave a driveway
- Rustic gravel. Gravel is one of the most economical paving options for a driveway.
- Permanent Asphalt. Tarmac is usually pretty affordable.
- Stylish tar and chip. A tar and grit driveway is an affordable driveway option that often has a more decorative appearance than regular asphalt.
- Easy to maintain concrete.
What is the compaction rate of asphalt?
Remember that when a vibratory screed is used, the compaction rate is typically around 6mm (1/4″) per 25mm (1″) of screed thickness and around 5mm (1/5″) per 25 mm (1″) when using a tamper and vibrating screed. Always check the compaction rate of the fresh layer when building a longitudinal joint.
What area does 1 tonne of asphalt cover?
The minimum recommended depth for vehicular traffic is 75mm, which means that 1 ton covers 7 square meters. For foot traffic, a depth of 50 mm is sufficient, so 1 tonne covers 10 square meters.
How many tonnes is 1 cubic meter of asphalt?
One tonne of asphalt is about 0.404 cubic meters (ANS ) .
How much does it cost to pave a driveway?
Asphalt paving costs an average of $30/m². However, prices vary from job to job. You can expect the cost of asphalt per m2 to be anywhere from $25/m2 to $40/m2.
How many square feet does 1 ton of 2 inch thick asphalt cover?
The area covered by 1 ton of asphalt depends on the thickness of the asphalt to be used; for a 1/4 inch section of asphalt, 1 ton covers approximately 316 square feet, while 1 ton of asphalt covers 79 square feet when laid several inches thick.
How long does a paved driveway last?
20 years
How is tonnage calculated?
Tonnage, in shipping the total number of tons registered or carried or the total deadweight tonnage. Gross tonnage is calculated from the formula GT = K1V, where V is the volume of a ship’s enclosed spaces in cubic meters and K1is a constant calculated by K1= 0.2 + 0.02 log10V.
How do you convert square feet to tons of asphalt?
A square yard is 9 sq ft. For a 4 inch thick asphalt pavement, the volume would be: 9 x (4/12) = 3 cubic feet. To determine how many tons, or fraction thereof, are required, divide by pounds per ton, or 2000 for an Imperial short ton.
Is asphalt driveway cheaper than concrete?
Cost. Aside from maintenance costs, asphalt is generally much cheaper to install than concrete, with asphalt costing between $2.50 and $4.00. It’s not uncommon for a stained concrete driveway to cost over $15.00 per square foot with a smooth finish.
Is 2 inches of asphalt enough for a driveway?
The granular base aggregate used for a residential driveway is typically 6 to 8 inches. At this layer, residential driveways typically use 2 to 3 inches of asphalt, while commercial driveways use about 3 inches.
How many cubic yards are in a ton?
One cubic yard is equal to 27 cubic foot. You can find out how many cubic meters of material you need using the online calculator. As a general guide, 1 cubic yard of aggregate, sand, or soil equals 1.5 tons.
How many tons is 1 yard of asphalt?
2.025 tons
How much does it cost a circular driveway?
By comparison, the cost of a simple concrete driveway is $3 to $10 per square foot, or $1,080 to $3,600 for a standard-size, two-car driveway, according to Costhelper. Custom concrete driveways with decorative elements can cost $15 to $25 per square foot or $5,400 to $9,000 total for the driveway.